How To Choose An Amplifier For Car Speakers

Amplifiers are the most crucial part of an audio system. No matter how good your subwoofer system is. Adding an amp to a car speaker will enhance the audio quality and improve performance. But it is important how to choose an amplifier for car speakers as there are many points to be checked while picking the amp.

An external amp can save you from the terrible audio from factory speakers while you prepare to replace them. Even the smallest external amp will help the system produce cleaner, deeper, louder, distortion-free music.

If you want your music to be loud, amplifiers are part of the picture. But whether you run your system-wide open or softly enough for conversation, a power amplifier will breathe life into your music, bringing out all of its excitement and detail. 

Before you pick up an amp, you must know how you will benefit by adding an amp to your audio system. Here are a few of the main benefits of adding an amp. So let’s start and read the full article.

Benefits of Adding An Amplifier

Better sound quality

Adding an amplifier gives you a clean power source to drive your speakers without straining. Unlike an amplifier built into an in-dash stereo, an external power amp isn’t limited by the space available — it can be designed without compromises. That means your music will sound cleaner and more defined at all volume levels.

Power for upgraded speakers

A factory system or an in-dash receiver may not do justice to your upgraded speakers. If you’re adding high-quality aftermarket speakers or component systems to your vehicle, they may require more power for peak performance than your existing in-dash receiver can provide.

Different sounds can fill a car’s interior. Hooting from the heavy traffic outside, a noisy engine, and air conditioning are the inevitable noise sources. A car stereo amplifier boosts the car audio sound and improves music clarity and intelligibility. At a higher volume, the car audio system completely overcomes noise sources.

As a result, an external amp allows you to enjoy whatever you listen to regardless of what’s happening outside.

Overcome other noises

Different sounds can fill a car’s interior. Hooting from the heavy traffic outside, a noisy engine, and air conditioning are the inevitable noise sources. A car stereo amplifier boosts the car audio sound and improves music clarity and intelligibility. At a higher volume, the car audio system completely overcomes noise sources.

As a result, an external amp allows you to enjoy whatever you listen to regardless of what’s happening outside.

Powering a subwoofer

Subwoofers require significantly more power than a brand-name or factory in-dash receiver can provide. A separate amp is a necessity.

Improves power efficiency

Everyone wants higher power efficiency in their car. Installing an amp enables you to improve the range in audio while avoiding increases in the use of car fuel. High-end amplifiers are popular for providing great power efficiency. In addition, a properly fitted amp contains sound inside the car.

A Simple Rule – Choosing An Amplifier for Speakers

If you’re designing a sound system, you will need to ensure that you choose speakers and amplifiers that work well together. If you choose the wrong amplifier for your speakers, you run the risk of causing damage to your equipment in the worst case or getting poor sound quality in the best case. 

This guide assumes you’ve already chosen your speakers based on the type of sound system you’re designing. If you need some help choosing speakers, read the complete article, it will definitely help you. You can also check our other posts related to the selection of speakers. Once you’ve chosen your speakers, it’s time to pick out an amplifier that can power them.

In this post, you’ll learn what to consider when choosing an amplifier to power your speakers or subwoofers.

General Rule for Choosing an Amplifier

A general rule for choosing an amplifier is to select an amp that provides 1.5-2 times the continuous power rating of your speaker. It will ensure the speaker has enough power while leaving yourself 3 dB of headroom.

Let’s look at why this is a good guideline and what happens if you choose an underpowered or overpowered amplifier to power your speakers.

What to Consider When Choosing an Amplifier to Power Your Speakers

It’s important to choose an amplifier that’s well suited to power your speakers. For one, this will ensure the best sound quality possible, but it will also help protect your equipment. 

Choosing the wrong amplifier can put you at greater risk of causing damage to your speakers or the amplifier itself. I’ll help you find the important specifications for your speakers and your amplifier to ensure they are a good fit for each other.

There are two basic factors to consider when choosing an amp compatible with your speakers:

Impedance and Power. As you’ll see, these two factors are closely interrelated. 

Impedance

Impedance is measured in ohms and refers to the opposition a circuit presents to electrical current. A speaker will “impede” the flow of electricity being created by the amplifier.

The first step is to determine the nominal impedance of your speaker or speakers. You can find the nominal impedance of your speakers in the technical specifications on the manufacturer’s website. Often, the nominal impedance of a speaker will be written on the label of the speaker itself. The nominal impedance of most speakers is 4, 8, or 16 ohms.

Finding the total impedance can be more complicated if you connect multiple speakers to a single amplifier channel. 

Power

Power is measured in watts and refers to the energy transfer rate. The power rating of your speaker is mentioned in the technical specifications. 

You’ll probably find several power ratings. 

Peak power refers to the maximum short-term power a speaker can handle without damage. 

We’re more concerned with how much power a speaker can handle over an extended period. It is the continuous power rating of the speaker. 

RMS or AES specifications might be used instead of continuous power ratings depending on the manufacturer.

Some speakers will provide more sound than others when supplied with the same power level from the amplifier. More power doesn’t necessarily mean louder. The loudness is ultimately determined by the speaker’s sensitivity, which can vary.

Using an Overpowered or Underpowered Amplifier

Choosing an amplifier that can supply too much power makes it possible to exceed the speaker’s limitations. 

As you start to hear that speaker distortion, you’d hopefully turn it down to keep your equipment safe. The speaker will start distorting, which is dangerous to the speaker. When it reaches that point, you should turn the amplifier down. 

As long as the overpowered amplifier isn’t set hot enough to provide too much power to the speaker, it will be capable of providing adequate power to the speaker with ease!

On the other hand, choosing an underpowered amp that struggles to supply enough power to the speaker is more likely to cause damage. 

There won’t be enough power to operate the speaker at its optimum level with an underpowered amp. You might tend to keep turning up the signal again and again. But at a certain point, that will only cause clipping of the system. The speakers won’t get any louder, but the waveform will become distorted, which could cause the speakers to overheat.

Conclusion

Matching the right amplifier is not simple. Because any equipment combination you get could damage if the improper gain structure is used. So it is good to do well research on how to choose an amplifier for car speakers

If you don’t understand the concept well, you will take advice from specialists, saving you from great loss.

Specialists recommended choosing an amplifier capable of providing about twice the speaker’s continuous power rating. It will allow the amplifier to provide adequate power to the speaker while maintaining some extra headroom to avoid the tendency to overdrive the input of the amplifier. Remember, a doubling of power is only a three-decibel change.

The best way to prevent damage and get the best sound quality possible is to choose speakers designed to provide an adequate sound pressure level for the application at hand. That way, you won’t tend to turn up the speakers beyond their limitations. 

I hope this article helps find the right amplifier for your car’s audio system. For other queries, you might check our related article.

Leave a Comment